This Glue item by PolymerClayLatvia has 29 favorites from shoppers. Ships from Latvia. Listed on Nov 15, 2023
Bison Epoxy Universal
Product information:
* Super-strong (up to 170 kg/cm²)
* Resistant to temperatures between -30°C and +80°C
* Filling
* Water resistant
* Chemical resistant
* Paintable
Suitable for:
Ideal for repairs to metal, ceramics, porcelain, crystal, glass, ivory, pearls, precious stones and various synthetics (polyester, bakelite, formica, rigid polystyrene and acrylic glass)
GETTING STARTED
Before Use:
Working conditions: only apply at temperatures between +5°C and +35°C. Product cures by mixing the resin and hardener.
Personal safety: preferably wear gloves.
Surface requirements: the materials to be bonded must be dry, clean, free of dust and grease.
Preliminary surface treatment: degrease parts to be bonded with acetone. Roughen smooth surfaces (sandpaper).
Tools: mix the components in the double-syringe by means of the supplied mixing bowl and spatula.
During Use:
Handling of packaging: remove the spatula from the side of the double syringe, and the closure cap from the handle. Break the seal of the double syringe.
Directions for use:
Press out an equal amount of both components onto the enclosed mixing tray. Mix these two equal parts well with a synthetic spatula until a mixture is obtained with a homogeneous colour. Apply the mixture, which at room temperature (+20°C) remains toolable for about 1.5 hours, as a thin layer on one of the two materials. Join the materials and keep them in place for 7 hours. Be careful not to move the parts before the adhesive has cured. After use, clean the nozzle with a cloth and place the special cap in the handle on the double syringe. Resin and hardener must not come into contact with each other unless for usage.
Advice:
Some types of synthetics can not be joined such as polyethylene and polypropylene. This can be tested by holding a glowing copper wire against the synthetics. Does it smell of wax? Then you can not bond it.
Use a piece of adhesive tape in order to keep the parts in place while the adhesive is curing.
Points of attention
After use close well (note: always place back the cap in the same way, due to the bonding of the cap to the double syringe). For optimum performance it is important to create a larger amount of adhesive and mix it very well. Curing time depends on the temperature. Adhesive does not cure below +5°C.
After Use:
Stains/residue
Remove wet stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically.
Storage conditions:
Store cool, dry, frost-free, upright (nozzle upwards) and tightly closed.
Bison Epoxy Universal, Strong Dual-component Epoxy Adhesive, Transparent Epoxy Glue for All Materials and Surfaces, Water Resistant Material
Adhesive Bison - Montage Kit Polysterine 310g - P&P Ilikodomiki LTD
Liquid Polymer Clay Adhesive - Denmark
Bison Product
BISON EPOXY 5 MINUTES, 100C, 24ml.
2PC/set Super Strong Epoxy Clear Glue AB Adhesive Acrylic Structural Adhesive for Cold Weld Plastic Metals Glass Rubber - AliExpress
Liquid Polymer Clay Adhesive
Epoxy glue Bison 2k / EPOXY UNIVERSAL 24 ml
Bison Epoxy 2 Part Epoxy Waterproof Adhesive – Fox's Chandlery
Epoxy Glue - UK
Crystal Clear, Paintable Universal, suitable for many materials Resistant to temperatures, Water resistant, Chemical resistant
BISON EPOXY Crystal Clear 5 Minutes Fast Two-Component Epoxy Glue Adhesive
Bison Epoxy Resin Adhesive, 5 Minutes, Clear, 24 ml : : DIY & Tools
Bison Product
Bison Kit Adhesive Glue, PDF, Adhesive
Liquid Glass Epoxy - Canada