Shop Wholesale Marine for the lowest prices on Interlux Nautical Enamel. This one-part topside paint delivers professional results. Choose from 3 finishes.
Interlux Nautical Enamel - Gallon
Nautical Enamels are one-part professional quality interior and exterior alkyd enamels. Economically priced and formulated to provide performance, value and reliability these finishes are durable and offers toughness, chemical resistance and excellent hide and wear characteristics. Nautical Enamels are ideal for decks, hulls and interiors in the marine environment. Nautical Enamels are available in a high gloss, semi gloss and flat finish and can be applied to any properly prepared fiberglass, metal or wood surfaces above the waterline, inside or out.
Features & Benefits:
Easy application
High hiding characteristics
Excellent flow and leveling
Great stain resistance to grease, oil and water
High solids and low V.O.C.
For interior and exterior use
***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
Application Instructions
HOW TO APPLY INTERLUX NAUTICAL ENAMEL
Mixing Stir well before and during use.
Cleaner Mineral Spirits or Naphtha
Thinning: Do not thin
Ventilation and Humidity Control Apply in dry, well ventilated conditions, Avoid excessively humid conditions, over 80% relative humidity.
Brush Natural bristle brush
Roller Use a solvent resistant small closed cell foam roller
Airless Spray: Tip Size: 0.33 mm/13 thou. Pressure adjust as needed.
Application Methods
Brush
Roller
Airless Spray
Preparation
Bare Fiberglass
Scrub the surface thoroughly with a stiff brush using soap and water.
Flush with fresh water to remove the soap residue and allow surface to dry. Remove surface contamination by wiping down the surface with Mineral Spirits or Naphtha using the two-rag method.
Fill any surface imperfections with approved filler for alkyd topside paint use. Sand the entire surface with 220-grit sandpaper until a flat matte finish is obtained.
Wipe the sanding residue off the surface with Mineral Spirits or Naphtha using the two-rag method.
If the surface is in poor condition and to achieve optimal results, use a primer approved for alkyd topside paints as per manufacturer’s instructions.
Previously Painted Surface – Good Condition
Remove all traces of loose paint by sanding the entire surface with 220-grit wet-or-dry sandpaper; wipe surface clean with Mineral Spirits or Naphtha using the two-rag method before and after sanding.
To achieve optimal results, use a primer approved for alkyd topside paints as per manufacturer’s instructions.
Previously Painted Surface – Poor Condition
Completely remove old paint.
After all old paint has been removed, follow preparation instructions for bare fiberglass.
Bare Wood
Scrub the surface thoroughly with a stiff brush using soap and water.
Flush with fresh water to remove the soap residue and allow surface to dry.
Remove surface contamination by wiping down the surface with Mineral Spirits or Naphtha using the two-rag method. Fill any surface imperfections with approved filler for topside paint use.
Sand the entire surface with 220-grit sandpaper until a flat matte finish is obtained. Wipe the sanding residue off the surface with Mineral Spirits or Naphtha using the two-rag method.
If the surface is in poor condition, and to achieve optimal results, use a primer approved for alkyd topside paints as per manufacturer’s instructions.
Metals
Apply a metal primer approved for alkyd topside paints as per manufacturer’s instructions.
Do not apply Nautical Enamel directly to bare metal.
Clear Epoxy
Nautical Enamel cannot be applied directly to clear epoxy. Clear epoxy when drying create amine blush which must be removed prior to applying paint.
Allow the epoxy to cure for 3-5 days in hot weather or 7 days in cold weather. Scrub the surface using soap and water using a stiff brush.
Sand the surface using 80-grit sandpaper (preferably wet). Remove the sanding residue by wiping down the surface with Mineral Spirits or Naphtha using the two…
Marine Topside Commercial High Durability Enamel Boat Paint Safety Orange Gallon
Duralux M734-1 1G Marine Enl Alpine Green (4 Pack)
Rust-Oleum Marine Coatings Boat Bottom Antifouling Paint Flat Black Enamel Oil-based Marine Paint (1-quart) in the Marine Paint department at
Traditional Alkyd Enamel - Satin
Topside Marine Polyurethane Paint
A single package topside enamel in quart size for use on primed steel and metal, wood, aluminum, or fiberglass. Duralux Marine Enamels withstand
Duralux Topside Marine Enamel, High Gloss, Quart
High-performance low-odor water-based marine-grade enamel paint provides a beautiful extremely durable smooth semi-gloss finish above the waterline on interior and exterior surfaces.
TotalBoat Elixir Enamel | Water-Based Marine Paint (Classic Whaler Blue, quart)
Duralux Marine Paint - Spray Paint Enamels – Pro Solutions Direct
Rust-Oleum Marine Coatings Topside Paint Gloss Bright Red Enamel Oil-based Marine Paint (1-quart) in the Marine Paint department at
Rust-Oleum Gloss Black Enamel Oil-based Marine Paint (1-quart) in the Marine Paint department at
Marine Coatings Topside Paint Product Page
Marine Enamels