DetailsCreate classic circular soap with this traditional round silicone mold. This is our favorite mold to use with our rubber duckies or luffas. A festive rubber duck can be found for most holidays, and luffa soap is perfect for pedicures. Mold walls are built with extra thickness to prevent bowing. Material: Food Grade Silicone Maximum Product Pour Temp: 500ºF Approximate Bar Weight: 1.5 oz Measures: 2 x 2 x .75 inches Made in China Melt & Pour Soap: Pour melted soap into silicone mold cavities. Allow soap to cool at room temperature until hard. Carefully remove soap from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the soap and carefully pull out of the mold. Cold Process Soap: Pour soap at trace into the mold cavities. After at least 24 hours, gently pull silicone mold to loosen its grip on the soap. Flip mold over onto a clean surface and gently push on the bottom of mold until the soap starts to release. Grab hold of the soap with a gloved hand, and allow soap to cure for 4-8 weeks. Note that some cold process soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster. Cold Process/Oven Process Soap: Pour soap at trace into the mold cavities. Preheat oven to 170ºF then place mold in oven. Turn oven off, and keep soap in oven overnight. The next day remove mold from oven. Carefully remove soap from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the soap and carefully pull out of the mold. Allow soap to cure for 2 to 4 weeks. Hot Process Soap: Scoop hot process soap into mold cavities. Gently tap the mold onto the counter to remove air pockets. Allow soap to cool and harden. (This can take up to 48 hours.) Carefully remove soap from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the soap and carefully pull out of the mold. Lotion Bars: Pour melted lotion bar mixture into mold cavities. Allow mixture to solidify. Carefully remove lotion bars from mold by gently pulling the sides away from the lotion bars, and then push on the bottom of the mold until the lotion bars starts to release. Grab hold of lotion bar and carefully pull out of mold. Care: Hand wash in warm sudsy water.
Sakolla Oreo Molds Silicone Chocolate Covered Cookie Molds 3 PCS 12-Cavity Round Silicone Baking Molds for Cake, Candy, Pudding, Mini Soap (2 Rose Red + 1 Blue) - Yahoo Shopping
Shell Small Round Soap Mold (MW 161) - Crafter's Choice
Sakolla 2 PCS Round Chocolate Cookie Molds, Cylinder Silicone Mold, Pe — CHIMIYA
12-Cavity 6-oz Handmade Soap Bar Silicone Mold – Boowan Nicole
Soap Molds, Plastic Soap Molds, Melt & Pour Soap Molds, Wholesale Soap Molds
Hot Chocolate Bombs - VIDEO DIY Holiday Gifts
Sakolla 2 PCS Round Chocolate Cookie Molds, Cylinder Silicone Mold, Pe — CHIMIYA
12-Cavity 6-oz Handmade Soap Bar Silicone Mold – Boowan Nicole
Sakolla Oreo Molds Silicone Chocolate Covered Cookie Molds 3 PCS 12-Cavity Round Silicone Baking Molds for Cake, Candy, Pudding, Mini Soap (2 Rose Red + 1 Blue) - Yahoo Shopping
Where to Buy Cute and Affordable Soap Moulds
Large 6-Cavity Cake Molds - Non-Stick Silicone Pastry Molds for Desserts, Cakes, and Soaps
6 Bar Rounded Rectangle Silicone Soap Mold - CandleScience
The traditional tart comes in a new dress thanks to Kit Tarte Ring Round Ø100mm by Silikomart. The kit is composed by two elements: four rings with a 100mm diameter in thermoplastic composite crush-proof material suitable for baking and creating the base and a silicone mold made up four cavities of 85mm diameter each to make a mousse or a cream to lay over the shortcrust pastry.
Silikomartkit Tarte Ring Silicone Mold with Heat-Resistant Plastic Ring (3.94 Dia x 0.78 H, 4 Cavities)