Shop High Quality EMPIRE DVP30MS 28in Medium Steel Spirit Direct Vent Gas Stove, available at US Fireplace Store. Free Shipping | Lowest Price Guarantee. Spirit Stoves are available in two types of ignition, Millivolt and Intermittent Pilot. Part No: DVP30MS30FP, DVP30MS30FN, DVP30MS70FP, DVP30MS70FN.
OVERVIEW
A Direct-Vent system uses two vent pipes. One draws air in from outdoors to support combustion. The other exhausts the by-products of combustion to the outside. The two vent pipes may be concentric (exhaust pipe within a larger diameter intake pipe) or co-linear (separate pipes of about the same size).
Combustion takes place inside a sealed chamber – with a glass front in the
case of a fireplace. Room air circulates around the combustion chamber, often assisted by a blower, to heat the room.
A DV system is often installed along an outside wall to simplify the vent run,
but can also be installed elsewhere in the home and vented through the roof.
Advantages:
Good efficiency – 60 to 80%
Good heat output with thermal transfer through the glass and air circulation
Separates room air from combustion air
May be used as primary heat source
Can operate with a remote or thermostat
Most systems can provide life-saving heat during a winter power outage
Empire Steel Stoves
Our direct vent steel stoves showcase Empire's slope glaze burner system. This modern design features clean lines and an extended ember bed for added glow. The Spirit Series is offered in 2 sizes, allowing versitility for a range of room spaces. The hand painted ceramic fiber log set creates a realistic effect that brings the warmth and comfort to your home.
Spirit Stoves are available in two types of ignition.
i) Millivolt (MV)The Millivolt system lights a standing pilot with a pushbutton piezo ignitor. Once the standing pilot is lit, the MV system operates with an on/off switch concealed on the back of the stove or with one of Empire’s optional remote control systems.ii) Intermittent Pilot (IP)
IP systems eliminate the standing pilot for even greater energy savings. Pressing the on/off switch ignites the pilot, which then ignites the main burner. IP systems can also operate with an optional remote control system.
Includes AC Power Adaptor (120VAC) with battery backup (switches to battery during power outage)
Direct-Vent Spirit Stoves (DVP)
Direct-Vent Spirit Stoves include Empire’s Slope Glaze Burner system with expanded ember bed for extra glow. Ceramic beads within the burner swirl and tumble the gas to create naturally swirling flames that are indistinguishable from a wood fire. Topped off with the hand-painted ceramic fiber log set and glowing embers, the effect is stunningly realistic and guaranteed to keep you and your guests mesmerized for hours.
Features
Upto 26,500 BTU's
Steel construction
Slope glaze burner
Millivolt with On/Off Switch
Intermittent Pilot with On/Off Switch
Available in Natural Gas or Propane
Available Models
22 Spirit Steel Direct Vent Gas Stove (Small)
28 Spirit Steel Direct Vent Gas Stove (Medium)
Includes
4-piece Log Set
Fireplace Barrier Screen
Requires
45-Degree Elbow
RCK20 Replacement Control Cover required for RVKN or RVKP
Specifications
Model
DVP30MS
Dimensions
27 3/4 (H) x 28 1/4 (W) x 18 (D)
Venting
4x6 5/8 (Use Black where visible)
Input BTU/HR (KW/H) Max (Propane)
26,500
Input BTU/HR (KW/H) Min (Propane)
21,000
Input BTU/HR (KW/H) Max (Natural Gas)
26,500
Input BTU/HR (KW/H) Min (Natural Gas)
18,000
CA Residents: See Prop 65 WARNING
DOWNLOADS
Download Direct-Vent Stove Brochure
Download Installation Instructions and Owner's Manual
Download Installation Instructions Automatic Blower
Download Installation Instructions Black Porcelain Liner Kit
Clearances
Top of appliance (ceiling)
36 inches
Back Wall
2 inches
Side Wall
6 inches
Adjacent Corner Wall
4 inches
OPTIONS & ACCESSORIES
Black Porcelain Liner
Type: Liner
Finish: Black Porcelain
Ceramic liners are made by the manufacturer for specific fireplace units. They cannot be cut or they will fall apart
Automatic Variable Blower
Type: Variable Blower
Automatic variable speed Blower for Empire heritage cast iron gas stoves
Improves efficiency and air distribution
Fits with Compact cast iron stove
GF24 Flexible 24 Stainless Steel Gas Line
Flexible Fas Line
Finish: Stainless Steel
Conversion Kit
Propane to Natural Gas
Natural Gas to Propane
Click to see Control Options
FRBC Battery Operated On or Off Remote Control
Turn burner OFF and ON using two-button handheld remote (Adjust flame from low to high using knob on the valve)
Does not require running wire to the fireplace
Requires batteries for the receiver and for the handheld remote
Operates during power outages
FRBTC2 Battery Operated Thermostat Remote Control
Type: Remote Control
Millivolt Control Options Only
Turns heater adjusts Thermostat
Battery-operated remote control
FREC Electric On-Off Remote Control with Battery Transmitter
Millivolt Control Options Only
Remote control with Battery transmitter for Empire remote-ready appliances
Easy and convenient to use
The receiver must be plugged in.
FRBTPS Battery Operated Programmable Touch Screen Remote Control
Type: Remote Control
Millivolt Control Options Only
Programmable and easy to use
Battery-operated remote control
FWS1 Wall Switch On/Off
On-Off wall switch for Empire remote-ready appliances
Mounts conveniently on wall
TMV Wall Thermostat Reed Switch
Wall thermostat with reed switch for Empire remote-ready appliances
Mounts conveniently on wall
TRW Wall Thermostat Wireless Remote
Wall thermostat with wireless remote for Empire remote-ready appliances
Thermostat mounts conveniently on wall
Click to see 45-Degree Termination Kits
Model
Description
DVK45LP
Horizontal 45 Deg Vent Kit (For Propane only)
Includes: SD09261B, SD46DVAE45B, SD58DVADC, SD58DVAHSCH, SD58DVAWTEC.
DVK45NAT
Horizontal 45 Deg Vent Kit (For Natural only)
Includes: SD46DVA12B, SD46DVADC, SD46DVAE45B, SD46DVAHC, SD46DVAWT3.
DVKHP45
Horizontal Termination Vent Kit
Includes: SD46DVA08AB, SD46DVA09, SD46DVA24B, SD46DVADC, SD46DVAE45B, SD46DVAE90B, SD46DVAHC, SD46DVAWT3.
DVKVP45
Horizontal 45 Deg Vent Kit
Includes: SD46DVA12B, SD46DVA17TAB, SD46DVADC, SD46DVAE45B, SD46DVAE90B, SD46DVAHC, SD46DVAWT3.
Click to see Variable Remote (Intermittent Pilot)
Remote Kit for Natural Gas / Propane
Model: RVKN - Natural Gas
Model: RVKP - Propane
Type: Remote Kit
Variable Flame Height Kit
RCK30 Replacement Control Cover
Model: RCK30
Type: Control Cover
Replacement Control Cover
For use with:
Remote Kit, Variable Flame Height, Natural Gas (RVKN)
Remote Kit, Variable Flame Height, Propane (RVKP)
Click to see Venting Components
DuraVent 45-Degree Elbow
Finish: Galvanized & Black
Use to offset obstructions as needed.
Fully unitized, twist-lock construction.
Elbows swivel, allowing the lock to remain fully engaged while aligning to the desired direction.
The angle will remain fixed at 45°.
DuraVent 90-Degree Elbow
Finish: Galvanized & Black
Use to offset obstructions as needed.
Fully unitized, twist-lock construction.
Elbows swivel, allowing the lock to remain fully engaged while aligning to the desired direction.
The angle will remain fixed at 90°.
DuraVent 17 Elbow Strap
Use for supporting vent pipe between offsets.
DuraVent 6 to 60 Pipe Length
Finish: Galvanized & Black
Designed for appliances tested and listed for direct vent.
Features a fully unitized twist-lock construction in both 4” x 6 5⁄8” and 5” x 8” vent sizes.
Use of sealant is optional unless specified by the appliance manufacturer.
Black pipe lengths feature exterior laser-welded seams.
No beads or hems.
To calculate install length, subtract 1 1⁄2” for each joint.
DuraVent 11 to 17 & 17 to 24 Adjustable Pipe Length
Use of sealant is optional unless specified by the appliance manufacturer.
Available in black or galvalume exterior (both feature laser-welded outer wall seams).
DuraVent Wall Strap
Use to support vent pipe.
Provides 1” clearance.
Recommend installing Wall Straps at 4-foot intervals on vertical runs.
DuraVent Ceiling Firestop
Required for multi-story vertical installations on the second floor and any subsequent floors.
4x 6 5⁄8 style may vary.
DuraVent Decorative Cover
Use as a decorative cover for horizontal (through-wall) installations Fits over the Wall Thimble faceplate.
Also used to cover a Ceiling Support Box. Comes with an insulation ring to reduce air infiltration where the pipe slips through the thimble.
Painted black.
DuraVent Attic Insulation Shield
Required for installations that pass through an attic to prevent insulation and debris from accumulating near the vent.
Provides 1” clearance to combustibles.
Includes base w/tube, extension tube, and collar.
DuraVent Cathedral Ceiling Support Box
Use to pass through ceiling and support pipe.
May be used on vaulted or flat ceilings.
Painted black.
Trim and clamp included.
DuraVent Flat Roof Flashing
Use to weatherproof the penetration of vent pipe through the roof.
Use on flat roofs, chase enclosures, or masonry chimneys.
Storm Collar required.
Made of galvalume.
DuraVent Adjustable Roof Flashing
Use to weatherproof the penetration of vent pipe through the roof.
Select roof flashing based on pitch of the roof.
For pitches of 0/12 - 6/12.
Storm Collar required.
Made of galvalume.
DuraVent Steep Roof Flashing
Use to weatherproof the penetration of vent pipe through the roof.
Storm Collar required.
Made of galvalume.
DuraVent Dead Soft Aluminum Flashings
Available in sizes 4”x 6 5⁄8” and 5”x 8”, in 0/12-6/12 (shown) and 7/12-12/12 styles.
Made of malleable dead soft aluminum.
Use with metal or tile roofs.
DuraVent Storm Collar
Use to maintain a weather-tight resistant seal between the pipe and the flashing.
DuraVent High-Wind Termination Cap
Available in aluminum.
Use for vertical terminations only.
For vertical terminations only.
Provides improved performance in high wind conditions.
DuraVent Low-Profile Termination Cap
Available in aluminum and stainless steel (S).
Use for vertical terminations only.
Check the appliance manufacturer’s instructions to determine which caps are approved for use with their appliance.
DuraVent Wall Thimble
Use with Square Horizontal Cap only.
Provides a complete wall-pass-through and firestop.
Refer to the appliance manufacturer’s installation instructions for requirements.
May be required in Canada.
DuraVent Square Horizontal Termination Cap
Available in aluminum, stainless steel (S), and copper (C).
Use for standard and high-wind through-the-wall termination.
Check installation instructions for restrictions on horizontal cap terminations, such as minimum distance from windows and doors.
DuraVent Round Horizontal Termination Cap
Available in aluminum only.
Use for through-the-wall termination.
Check installation instructions for restrictions on horizontal cap terminations, such as minimum distance from windows and doors.
Check with the appliance manufacturer for approval.
DuraVent 14/36 Snorkel Termination Cap
Use for horizontal through-the-wall termination when a vertical rise is desired in the system to meet the appliance manufacturer's recommended minimum heights.
Do not enclose in the wall or install below grade.
DuraVent Sconce Termination Cap
Available in aluminum, stainless steel (S), and copper (C).
Use for horizontal through-the-wall termination.
Check installation instructions for restrictions on horizontal cap terminations, such as minimum distance from windows and doors.
Check with the appliance manufacturer for approval.
Patented.
DuraVent Square Horizontal H2 Termination Cap
Available with aluminum shroud.
Use for standard and high-wind through-the-wall termination.
Provides improved performance in high wind conditions.
Adjustable air intake and interchangeable shroud (shroud is included and required for all installations).
DuraVent High-Wind Sconce Termination Cap
Available in aluminum, stainless steel (S), and copper (C).
Use for horizontal through-the-wall termination.
Provides improved performance in high wind conditions.
Check installation instructions for restrictions on horizontal cap terminations, such as minimum distance from windows and doors.
DuraVent Snorkel H2 Termination Cap
Use for horizontal through-the-wall termination when a vertical rise is desired in the system to meet the appliance manufacturer's recommended minimum heights.
Features an adjustable air intake and interchangeable shroud (shroud is included and required for all installations).
WARRANTY
10-year limited warranty on combustion chamber, limited lifetime on glass.
All other parts carry a three-year limited warranty.
All remote controls carry a one-year limited warranty.
Overview Empire Cast Iron Stoves are available in two types of ignition Millivolt (MV) and Intermittent Pilot (IP). The Millivolt system lights a standing pilot with a pushbutton piezo ignitor. Once the standing pilot is lit, the MV system operates with an on/off switch concealed on the back of the stove or with one of Empires optional remote control systems. IP systems eliminate the standing pilot for even greater energy savings.
Empire Cast Iron Medium Vent Free GAS Stove - VFD30CC
Heritage Premium Medium Direct Vent Cast Iron Stove (Millivolt/Pilot) - Empire Comfort Systems
Empire VFD30CC30FP Heritage Cast Iron Matte Black VF Stove - LP : Home & Kitchen
Gas Stoves – US Fireplace Store
EMPIRE 28 Medium Steel Spirit Direct Vent Gas Stove - 26500 BTU – US Fireplace Store
American Hearth Spirit Direct-Vent Gas Cast Iron Stove - Hearth Appliances
Spirit Stoves - American Hearth
Gas Stoves – US Fireplace Store
Spirit Stoves - American Hearth
Stoves
American Hearth Spirit Direct-Vent Gas Cast Iron Stove - Hearth Appliances
Empire VFD30CC30FN Heritage Cast Iron Matte Black VF Stove - NG: Home & Kitchen
Sprit Stove Steel Vent-Free, Medium Nat by American Hearth Spirit Stoves are available in two types of ignition – Millivolt (MV) and Intermittent Pilot (IP). The Millivolt system lights a standing pilot with a pushbutton piezo ignitor. Once the standing pilot is lit, the MV system operates with an on/off switch concealed on the back of the stove or with one of Empire’s optional remote control systems. IP systems eliminate the standing pilot for even greater energy savings.
American Hearth - Sprit Stove Steel Vent-Free, Medium Propane
Overview Empire Cast Iron Stoves are available in two types of ignition Millivolt (MV) and Intermittent Pilot (IP). The Millivolt system lights a standing pilot with a pushbutton piezo ignitor. Once the standing pilot is lit, the MV system operates with an on/off switch concealed on the back of the stove or with one of Empires optional remote control systems. IP systems eliminate the standing pilot for even greater energy savings.
Empire DVP20CC Compact Cast Iron Direct Vent GAS Stove Liquid Propane / Intermittent Pilot / Porcelain Black
EMPIRE 22 Small Spirit Steel Vent Free Gas Stove - 20000 BTU – US Fireplace Store